LigoWave DLB 5-15ac Long Range Point to Point configuration

LigoWave DLB series is a 5 GHz outdoor point to point and point to multi point wireless radio for long range connectivity. DLB 5-15ac is gigabit wireless radio for up to 7 KM point to point and up to 5 Km point to multi point wireless connectivity. DLB 5-15ac is outdoor radio with integrated antenna and IP 65 outdoor enclosure to work on all weather. LigoWave DLB series best for CCTV and internet high throughput up to 500Mbps as per official website. Configuration of Ligowave DLB not very complicated but to get higher throughput and stable point to point connectivity configuration should be best tune.

In this post I will describe you step to step how to configure Ligowave DLB 5-15ac point to point configuration for long distance and higher interference area. Configuration of Ligowave DLB in Point to point required 2 DLB 5-15 radio and configuration in Point to Multi point required at least 3 DLB 5-15 radio. To proceed your Ligowave DLB series point to point configuration ready your both radio,and follow the steps below to setup a stable and reliable wireless connectivity. DLB 5-15ac having 1 Gigabit Ethernet with 24Volt PoE support.

LigoWave DLB 5-15 Point to Point Connection Diagram

To configuration of DLB 5-15ac first required a physical connection to access the device on web browser. Both side radio will be configure first on table and after successful point to point configuration and testing you can deploy on site. To connection of LigoWave device take the PoE adapter comes with device. Now take the device and connect the PoE out port to device with cat6 cable. Connect Lan port to Laptop/Desktop Lan port to access device on web browser to make configuration for point to point bridging. Power on the PoE adapter to get power on Ligowave DLB 5-15ac. Connection will be same for both AP and Client device to configuration on table and for real sites. After connection next steps is access the Ligo wave device on Laptop and configure one device as AP+WDS and second device Client WDS.

LigoWave Point to Point Scenario

Point to point scenario of Ligowave DLB series , LigoWave infinity or any wireless device almost same. One side device will be configure as Access Point WDS and remote side device configure as a client WDS. Everything manage from Access Point WDS device such as channel, channel Width, client will auto change the settings once connected access point device successfully. In this post I will show you step to step how to configure Ligowave DLB series Point to Point and Ponit to Multi Point configuration. For point to Point Wireless connectivity Device configuration

1:- Location A – Access Point mode

2:-Location B- Client WDS mode

LigoWave DLB 5-15ac Default Settings and Login first time

To access LigoWave device first required default login setting. Get all brand Default settings here For LigoWave default IP Address is – 192.168.2.66 Default username and password = admin/admin Use the 192.168.2.x series IP address in Laptop/Desktop LAN port EXp- use 192.168.2.10 in Laptop LAN. See here how to configure Laptop LAN IP Address. Open Web browser and Type 192.168.2.66 and hit enter.

Use admin/admin for default login You can change Language as per your country language.

Agree term & condition Operating

country– choose your country

5Ghz Antenna Gain– type your antenna gain in box to compliance EIRP Usage scenario – use the Point to point or Point to multi point Click Change button to save settings After login now change the LigoWave operation mode for next steps.

LigoWave DLB 5-15ac Access Point WDS Mode

First device will be configuration as AP WDS mode to configuration for Wireless point to point connectivity. To configure Ligowave in AP WDS mode follow steps below. After login DLB 5-15 go to setting gear icon of top menu. Operation Mode- choose Access Point WDS Mode

Now Increase or reduce the LigoWave AP device Tx power and configure the SSID and Security key.

Tx Power- move the button to increase and reduce power as per distance of your Point to point.
Click Setting gear icon to change SSID name and configure security.

SSID- use the network name to recognize your radio while scanning form remote site radio.
Security- set security to protect your LigoWave Point to Point connectivity.

Click Done button to save changes.

By default LigoWave DLB 5-15 Channel set as Auto mode. If you are going to use LigoWave in city where high interference area than use the manual channel selection. See below how to set manual frequency in LigoWave DLB 5-15ac. Channel – Auto/40 Click and choose the manual channel.

After all settings on Access Point mode Device save changes to apply all settings. Click Save changes to settings take effected. This the one side Device configuration of point to point connectivity. Please keep Access point device on and connect second device with Laptop.

2: Ligowave DLB 5-15ac Client WDS Mode Configuration.

Now configure remote side Ligowave device with Client mode. Client mode will required LAN IP configuration, and other parameters client will auto detect from AP WDS. Login Device as follow above steps. After login change IP Address first because Ligowave both device comes with default IP address. You can change both side IP Address according to your but both radio should have unique IP address to avoid conflict issue. LigoWave DLB 5-15ac LAN IP Address Configuration. 1-To change Ligowave LAN IP address go to settings option and choose second LAN icon from left vertical menu. 2:- IP Method- choose static IP 3:- IP Address- change IP Address here

After change IP address you will get a pop-up notification to re-open Ligowave with new IP Address.

Re-Login LigoWave DLB 5-15 device to configure device as client mode.

Click settings Icon
Operation mode – choose Station WDS
Tx Power- reduce and increase tx power as per location distance.

Click Save change to station mode. Now scan the client mode device for Access Point WDS device. Click Search Icon to scan your AP device from client

You will get many AP running on your area, choose the your AP ssid from List and click select button.

Lock AP by MAC address – check this option (locking mac will always keep connected to same device. Click Done button Click save change now to apply settings. Device will start saving and reboot, this process take 10-20 secon. Wait until device refresh again. Login and check the Point to Point connected status. Go to (i) information icon to top menu See the Wireless connected status. You can see SSID, Device MAC details, signal status and link connected time.

LigoWave DLB 5-15ac Point to Multi Point configuration.

LigoWave DLB 5-15 configuration is same like point to point configuration. You just need to repeat the client WDS again with third device for next location. You can connect multiple device with repeating client WDS mode configuration.

How to Connect Any Wi-Fi without Password from Mobile?

How to Configure UBNT Rocket M2 as Access Point Mode?

Download LigoWave Firmware and Reset Tool Now

The post LigoWave DLB 5-15ac Long Range Point to Point configuration appeared first on .

from https://ift.tt/2kum8mL

Techytricks

Search This Blog